Service available now · 50 states Mon–Sun · 7AM–9PM EST

Amana Washer Agitator Not Working: Causes and Checks

TL;DR: When an Amana washer agitator stops moving, check the load size, the lid and the cycle first. If the motor hums but the agitator stays still, stop the washer and call a technician; the drive between motor and agitator is not an owner repair.

Updated Nov 17, 2026 5 min read
TL;DR: When an Amana washer agitator stops moving, check the load size, the lid and the cycle first. If the motor hums but the agitator stays still, stop the washer and call a technician; the drive between motor and agitator is not an owner repair.

When the agitator in an Amana top-load washer stops moving, the clothes just sit in the water and come out barely washed. The cause can be as simple as an overloaded drum, or as involved as a worn part in the drive that links the motor to the agitator. This guide helps you sort the two: what to look at first, what a stuck agitator tells you, which checks are safe and when to stop and call a technician. Our pages describe Amana top-load washers with a Dual Action Agitator, and we do not name a single failed part as the cause here, because several things can stop an agitator and only a technician can tell which. The guide gives no codes, because a stopped agitator does not point to one.

Agitator does not move, tub fillsCheck the load, the lid and the cycle first
Agitator moves weakly with a big loadOverloaded or packed drum
Motor hums, agitator stillStop the cycle; a technician should check the drive
Washer drains and spins normallyThe fault is likely in the agitating drive, not the whole washer
NeverReach into the tub or open the cabinet

Why is my Amana washer agitator not working?

An agitator is the part that twists the clothes through the water during the wash phase. Our guide to how an Amana high-efficiency washer works describes the Dual Action Agitator on a top-load NTW as the way these washers clean by movement. When it stops, one of three things is usually going on. Either the washer is not being asked to agitate, for example because of the cycle you selected or because the lid is not sensed as closed. Or the load is too heavy or packed for it to move. Or the drive that links the motor to the agitator has a problem. The first two you can check yourself; the third needs a technician.

Notice what the washer does apart from the agitator. If it fills, drains and spins normally and only the agitating stops, the fault is probably in the agitating drive. If it will not fill, will not start or shows a code, the problem is probably more general, and our guides on a washer that will not start and a washer that will not spin may fit better.

What should you check first?

Stop the cycle and open the lid. Look at the load. A drum packed with towels or a heavy comforter can stop the agitator, or make it move only a little. Take out some items, spread the rest loosely and restart. Close the lid firmly: a top-load washer will not agitate or spin unless it senses the lid as closed, and our wont-spin guide explains that the washer needs the lid lock and strike lined up. Check which cycle you chose, since some gentle or soak settings agitate very little, and the manual describes how each behaves.

Also check the amount of detergent. Too much creates suds, which can slow or interrupt a cycle, and our suds error guide explains it. If the washer seems to be working but slowly, give it time to complete a phase before you decide it has failed.

A close-up of the central post inside an empty washing machine tub with no water
The agitator is the post that moves clothes through the water during the wash.

What does a stuck agitator tell you?

Listen. A motor that hums or runs while the agitator stands still means power is reaching the motor but the movement is not reaching the agitator, which points to the drive. A loud grinding or a burning smell means stop the washer at once. A washer that works but with a very weak motion may be overloaded or have a wearing part. If the agitator moves freely by hand with the washer off and unplugged, that does not mean it is fine; the part that links it to the motor may be worn or damaged.

You can safely test one thing: with the washer unplugged and the tub empty, gently check whether the agitator wobbles or is loose on its shaft. If it is loose, do not run the washer. Do not try to pull the agitator off, force it or open the cabinet, because the parts underneath are a technician’s job. Never put a hand in the tub while the washer is plugged in and powered.

What can a technician find?

The agitating motion comes from a chain of parts: the motor, the parts that connect it to the drive and the drive that turns the agitator. A technician will check which link has failed, and a wear or breakage in that chain is the classic reason for an agitator that does not move while the washer otherwise works. Our guides do not name the part for your model, so we do not guess. They do say that diagnosis is by symptom for these washers, so a clear description helps: what the washer does, what you hear and when it stopped.

Once the cause is found, our washer repair or replace guide helps you decide if the repair is worth it. If the washer is old and has had other problems, it may be a replacement case.

When should you call a technician?

Call if the agitator still does not move after you reduce the load, close the lid and choose a normal cycle, if the motor hums without movement or if you notice grinding, burning or water leaking. If you see water around the washer, sparks or a burning smell, switch off the breaker at the panel while standing on a dry floor, and never pull a plug from a wet outlet. We are an independent repair company. Read about our Amana washer repair or schedule a visit, and describe what the washer does and what you hear.

Frequently asked questions
Why is my Amana washer agitator not moving?
Common reasons are an overloaded drum, a lid that is not sensed as closed, a gentle cycle, or a worn part in the drive between the motor and the agitator. Check the first three yourself.
Is the agitator the same as the spin?
No. The agitator moves the clothes during the wash and the drum spins to remove water. A washer can spin and drain normally while the agitator fails.
Can I fix a stuck agitator myself?
You can reduce the load and check the lid and cycle. Do not pull off the agitator or open the cabinet; the drive is a technician’s job.
Is it dangerous to reach into the tub?
Yes, if the washer is powered. Stop the cycle first and never put your hand in a moving tub.
When should I call a technician?
Call if the agitator does not move after the simple checks or if you hear grinding or smell burning. You can book a visit online.

Schedule Amana
appliance repair

Experienced technicians in all 50 US states. Average response within 24 hours.

  • Experienced Amana specialists
  • Genuine OEM parts
  • 30-day labor warranty
  • Upfront pricing
Need professional help?

Book experienced Amana
appliance repair

On-site diagnostics, genuine OEM parts, 30-day labor warranty. Service in all 50 US states.